Hilka Pro-Craft Stud Extractor Set 8 Pcs Product Code: 20084

€14.45
Most popular sizes of stud extractors. Manufactured from high grade tool steel. Supplied in a handy carrying case.
Additional Information
Technical Specification
  • Brand : Hilka Pro-Craft
  • Product Type : Stud Extractor Set
  • Pack Size : 1
  • Manufacturer Guarantee : 1 Year Guarantee
  • Pieces in Pack/Case : 8
Product Contents
4, 5, 6, 7, 10, 13, 19 and 24mm.
Delivery & Returns

DELIVERY

Standard delivery service up to 3 working days: €8.95

Free delivery on all orders over €70.00


Click here to see information on our delivery service

 

RETURNS

Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.

 

Click here to see information on returns and cancellation

€14.45 Incl. 23% VAT

Add to Wishlist

More Items to Consider

Loading... Loading...
1
Hilka Pro-Craft Stud Extractor Set 8 Pcs is rated 2.7 out of 5 by 23.
Rated 1 out of 5 by from Toy tools.........Rubbish Needed to get a couple of car wheel bolts out that had snapped. Drilled them out to 6mm and tried the 4th smallest, as other reviewers have noted the square end is too small and wrong shape and impossible to get any leverage. Gave up drilled the holes to 8mm and tried the next size up, fashioned something to go over the end so I could get a small bar on it and it snapped within 5 seconds of it biting. Waste of time and money.
Date published: 2018-04-22
Rated 1 out of 5 by from did it extract?? bought these to extract a bolt from an aluminium engine block. the broken bolt was not corroded or cross threaded. Used the biggest extractor i could....snapped off. now in a worse corner than i was before. very, very poor quality. should have stopped when i saw the end of the extractor was losing it thread immediately after i put it in. would recommend you avoid this product
Date published: 2018-04-09
Rated 2 out of 5 by from Wary! Bought to remove an inaccessible stud in a van turbo, very wary of doing further damage. Advised drilling sizes would have been helpful. Had good quality tap wrenches available but unable to turn smaller extractors due to inadequate square drive on extractor. Not convinced of quality I didn’t risk increasing torque in fear of tool breaking in the turbo.
Date published: 2018-03-16
Rated 5 out of 5 by from Great piece of kit The wannabe F1 pit crew at a local tyre fitters not only managed to damage my locking wheel bolts and key nut, but also did not tell me. Six months down the line, when the car needed a new clutch, garage had difficulty removing the wheel, leaving me with the three remaining bolts to deal with. Drilled the bolt working up from 4mm to 10mm, taking frequent breaks to avoid overheating the bolt and drill bits. Finally tapered the hole slightly and used the No#6 extractor, and your mother has a brother called Robert - bolt came out. Tips for use - drill as large a hole in the bolt as you can, so you can use the sturdiest extractor for the job. When screwing in the extractor keep it as straight to the shank of the bolt as possible.and give it a tap with each turn. Once it has bitten, use a large adjustable spanner or stilson to turn. Marked down slightly, because of the square, rather than hexagonal, ends of the extractors.
Date published: 2018-02-22
Rated 5 out of 5 by from Perfect for the job Worked perfectly to remove a sheared PVC fitting from a housing it snapped in.
Date published: 2018-01-25
Rated 5 out of 5 by from Works great Used it to extract socket for shower elbow after tiling, tiler pack up tiles so it was to far in to screw in elbow. This worked a treat, otherwise would have to remove tiles as pliers would not get in. I do not think this is for high tensile steal but work great on brass and iron fittings
Date published: 2017-08-20
Rated 1 out of 5 by from Not fit for purpose I bought this product for the purpose of extracting a high tensile bolt. I drilled a large hole with enough depth to apply the second largest extractor. I managed to get the extractor to start to cut it's own threads and grip, then I started to apply more torques carefully hoping the extractor was gripping the stud more and more, buy when it failed and fell out, It was immediately obvious the material from which the extractor was made was far too soft. All of the threads on the extractor had gone. This is just not fit for purpose.
Date published: 2017-08-02
Rated 5 out of 5 by from does the job got the job done just the ticket very well made good value for the moneywill never worry about shearing a bolt again
Date published: 2017-04-11
  • y_2018, m_8, d_13, h_21
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.8
  • cp_1, bvpage1
  • co_hasreviews, tv_1, tr_22
  • loc_en_IE, sid_20084, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix-ie