Non-Woven Preparation Wheel 115mm Product Code: 83915

Non-woven material. For use with 4½" / 115mm angle grinders (max. operating speed 11,500rpm). Removes paint, varnish, rust and scale from metal, wood, fibreglass, granite, brick or stone. Non-clogging.


Diameter: 115mm. Bore: . Max 13,300rpm.
Additional Information
Technical Specification
  • Brand : Unbranded
  • Product Height : 20 mm
  • Product Length : 120 mm
  • Product Type : Non-Woven Preparation Wheel
  • Total Product Weight : 0.08 kg
  • Product Width : 120 mm
  • Pack Size : 1
  • Product Diameter : 115 mm
  • Manufacturer Guarantee : 1 Year Guarantee
  • Pieces in Pack/Case : 1
Product Contents
Delivery & Returns


Standard delivery service up to 3 working days: €8.95

Free delivery on all orders over €70.00

Click here to see information on our delivery service



Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.


Click here to see information on returns and cancellation

€10.45 Incl. 23% VAT

Add to Wishlist

More Items to Consider

Loading... Loading...
Non-Woven Preparation Wheel 115mm is rated 3.7 out of 5 by 67.
Rated 4 out of 5 by from Did the job Good for removing surface rust and paint from metal.Did break up fairly quickly and deep dish shape makes it difficult to tighten onto angle grinder.
Date published: 2018-08-04
Rated 2 out of 5 by from prep wheel Purchased 2 for a job found that the wheel was too large and caught on grinder guard on my two grinders, also I couldn't tighten the retaining plate for the wheel as it’s too deep/thick for the spanner pegs to fit. Not used these yet so I can't say how they perform. not returned in the spares box !!
Date published: 2018-07-13
Rated 3 out of 5 by from Good for metal, not stone Have used these successfully to strip iron fireplaces so tried them on cut stonework of new house which has been masonry painted. Burned through 3 in 10 mins to. Cover only about 8 sq inches. Didn't damage the stone but neither the paint. Fine if your removing from metal. Or wood.
Date published: 2018-07-01
Rated 4 out of 5 by from Good performance poor life This disc shifts rust and mill scale faster and better than a twist knot brush, but wears out much faster. It's also very good for deburring steel fabrications and cleaning garden shears, limb loppers, and suchlike.
Date published: 2017-10-22
Rated 5 out of 5 by from Really good I've used the smaller drill version of this for years without complaint, I need a bigger version to cover a much larger area and have not been disappointed.
Date published: 2017-08-20
Rated 5 out of 5 by from perfect removing old paint bought to rremove old paint from stone. Works a treat, however only complets the job in a small area before needing a new disc. However nothing else worked so well so I've kjust had to get more. Value for money quesionable - but saved a lot of time...
Date published: 2017-08-20
Rated 4 out of 5 by from Paint removal Used it to take paint splashes off bricks and it did the job well. I tried a cheaper version of this from another well known store and it lasted less than half the time, definitely recommend this one.
Date published: 2017-08-20
Rated 5 out of 5 by from Goodbye old paint and rust I bought this as a bit of a gamble to help remove thick paint and rust from steel railings. Best new tech I've bought for years. Flat and very abrasive it removes smoothly, evenly and cleanly. Used it on old flaking paint on wood, and again it cuts prep time down by about 70%. It even helps to flatten damage on seasoned oak beams. Can't fault it. It seemed a bit expensive but after 2 hours of paint removal it's going well and already covered it's purchase cost.
Date published: 2017-08-08
  • y_2018, m_9, d_24, h_3
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.8
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_67
  • loc_en_IE, sid_83915, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix-ie