H & C Contemporary Bar Valve Fixing Kit Chrome Effect Product Code: 76919

€35.95
Brass construction with chrome effect finish. Suitable for use with bar showers.

Features

  • 2 Year Manufacturer's Guarantee (T&Cs Apply)

Specifications

Model: WP001.
Additional Information
Technical Specification
  • Brand : H and C
  • Product Type : Contemporary Bar Valve Fixing Kit Chrome Effect
  • Model No : WP001
  • Pack Size : 1
  • Manufacturer Guarantee : 2 Year Manufacturer's Guarantee (T&Cs Apply)
  • Pieces in Pack/Case : 1
Product Contents
Faceplate, 2 x adaptors, 2 x brass copper rings, 2 x compression nuts, 2 x SS304 flanges and 2 x screws.
Delivery & Returns

DELIVERY

Standard delivery service up to 3 working days: €8.95

Free delivery on all orders over €70.00


Click here to see information on our delivery service

 

RETURNS

Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.

 

Click here to see information on returns and cancellation

€35.95 Incl. 23% VAT

Add to Wishlist

More Items to Consider

Loading... Loading...
1
H & C Contemporary Bar Valve Fixing Kit Chrome Effect is rated 4.2 out of 5 by 44.
Rated 2 out of 5 by from Not for cavity walls Had to return this as I couldn’t make it work. When attached to a Mira Atom bar shower there’s about 14mm between the shroud and the inlet pipe, so in effect that’s 14mm for board, adhesive and tile, which for me is about 30mm. I can’t really work out in what situation I could make this work
Date published: 2018-05-22
Rated 5 out of 5 by from Can't fit "Mixer" without this After building a 75mm cavity to take a new Shower Mixer Valve and hidden pipe work this "Bar Valve Wall Kit" was then secured to the solid wall in the cavity which then accepted all the pipe work and importantly the weight of the Shower Mixer. Just leave enough thread sticking through to secure your mixer. It can be used either way up depending on the pipework. As I was using waterproof paneling on the front of the cavity, without the Valve Wall Mount being secured inside there is no way the Shower valve would hang on the panel. This was the find of the whole project.
Date published: 2018-04-15
Rated 4 out of 5 by from Great product It is w great product overall- really sturdy if installed correctly. My only issue is the screws are made of cheese- sheared one and rounded the other before I got near the wall. Other than that it’s a great product, easy to fit and level and holds weight well if you’re fitting a heavier shower.
Date published: 2018-03-29
Rated 4 out of 5 by from Easy to fit and works well I used this to replace an inferior fixing kit from Triton for a Triton mixer bar I was fitting. It was easy to fit and being sold brass there was no worry with cross threading the compression joints or doing them up tight enough to seal properly. I wish that I had bought this in the first place instead of going with the manufacturers recommended one.
Date published: 2018-03-06
Rated 2 out of 5 by from Too short! The concept is great, and I would continue to purchase these if the 3/4 tails were longer, but it is not long enough to go through 12mm ply, adhesive and tiles over 5mm thick, and trust me I tried everything I could think of to get it to work. In the end I had to spend £40 on shallow collars! I advise spend the extra money on bristan
Date published: 2018-02-14
Rated 5 out of 5 by from Makes external valves easy Great product, this allows you to put a level across and fit the the end feeds where needed all in the know that the new shower valve block will thread straight on with ease... not cheap but makes for a good finish and a sense of security
Date published: 2018-02-10
Rated 5 out of 5 by from perfect for anyone Best bit of kit for anyone installing a shower, keeps everything in line, so your pipes fit perfect. in the trade or not, you'll be able to fit this
Date published: 2018-01-15
Rated 3 out of 5 by from Watch out for tiling depth This is a well made adapter and would be very useful if the 3/4" pipes were about 20mm longer. I planned to use this behind a stud wall. The problem is that to keep the compression inlets behind 12.7mm board and 10mm tiles +adhesive 2mm does not leave enough thread protruding to attach the hole cover and bar valve, which must be done up tight ! A drawing would have been helpful ! I solved this by using an extension, to a 1/2" brass screw to the wall 90 deg, of a double female and double male brass connector and then Z connectors supplied with the Mira shower bar. Works well in a CLS stud wall with 10mm back packing.
Date published: 2018-01-05
  • y_2018, m_6, d_17, h_6
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.8
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_44
  • loc_en_IE, sid_76919, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix-ie