Diamond Core Drill Guide 10mm Product Code: 57014

Through-hardened for constant strength. Tough construction to withstand high torques. Should only be used with machines fitted with a clutch.


  • Tapered TCT Guide Drill
  • No Pre-Drilling Necessary


Guide drill. 10mm.
Additional Information
Technical Specification
  • Brand : Unbranded
  • Product Height : 15 mm
  • Product Length : 230 mm
  • Product Type : Diamond Tile Core Drill Guide
  • Total Product Weight : 0.08 kg
  • Product Width : 50 mm
  • Pack Size : 1
  • Shank Size : ½ "
  • Shank Type : Hex
  • Product Diameter : 10 mm
  • Manufacturer Guarantee : 2 Year Manufacturer's Guarantee (T&Cs Apply)
  • Pieces in Pack/Case : 1
Product Contents
Delivery & Returns


Standard delivery service up to 3 working days: €8.95

Free delivery on all orders over €70.00

Click here to see information on our delivery service



Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.


Click here to see information on returns and cancellation

€4.75 Incl. 23% VAT

Add to Wishlist

More Items to Consider

Loading... Loading...
Diamond Core Drill Guide 10mm is rated 4.3 out of 5 by 11.
Rated 5 out of 5 by from Just the job Good Quality - Good price - does the job absolutely fine - just need to ensure it is fully located in the arbor (sharp tap with a hammer does the job - maybe not the correct method but it worked for me) - performed very well with a large core drill thru brick and block
Date published: 2017-07-30
Rated 4 out of 5 by from Couldn't use it. Drilled 10mm guide hole from inside through 300mm cavity wall. Brick got little blown out on outside. Couldn't use the guide from outside as it was too short to reach the guide hole.
Date published: 2017-07-03
Rated 4 out of 5 by from Did The Job Bought this to go with the Erbauer Diamond Core Drill Bit 117mm x 150mm (73171) I needed to get through my wall. Wouldn't have known to get it of it wasn't for the helpful guys in the worthing store and it wouldn't have worked without this, or the Diamond Core Hex Arbor (34411).
Date published: 2016-12-09
Rated 4 out of 5 by from Done what it needed too Done what was required of the job for a good price.
Date published: 2015-10-13
Rated 3 out of 5 by from Works well If you look at "View more information" a length is given as 230mm whereas the bit itself it is 200mm, it is a taper shank rather than hex as stated in a couple of places (hex won't fit the arbor) and the shank more like 5/16" rather than 1/2". Drills a hole to guide a core bit without any issues.
Date published: 2015-07-20
Rated 5 out of 5 by from Super centering with this bit I always mean to have a spare in the "plumbing tools" box but always forget until one breaks. Using with 107mm core and holds centre excellently once I use my dead-blow hammer to fit in place. Cannot say the taper drills are easy to remove so why don't they just design an SDS special for the job?
Date published: 2015-05-20
Rated 4 out of 5 by from Good guide drill It did the job I bought it for, used it to bore through a 10" solid brick wall and it kept going right to the end and I feel that it will do more holes when necessary. It is very good for the price.
Date published: 2014-12-16
Rated 5 out of 5 by from Delighted with purchase The drill bit is of a good quality. Well worth the price. I needed replacement when my original one went off and end up in my cavity wall.
Date published: 2014-11-05
  • y_2017, m_11, d_23, h_21
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_11
  • loc_en_IE, sid_57014, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix-ie